SUBSCRIBE TODAY Smiley face  Get updates via email! 




We Are Flying Solo

August 23, 2014

No Cups? No Problem! Build Hassle-Free Jump Standards…For $0!

Building Standards 16 Aug 2014 001
Careful schematics (I defy 'smart'phone world!)
There are few necessary evils so maddening & so fiddly as The Jump Cup.

Buying them, drilling holes that aren’t too crooked, losing pins, dropping poles on your foot while adjusting them, breaking plastic cups, bending metal cups, deciding you don’t even like the kind you have…but do we have a choice?

YES!

Nostalgia had me paging through my well-worn Encyclopedia of the Horse (a 1977 masterpiece), when a training photo caught my eye.  It wasn’t the jumper, but rather the obstacle:  a simple, versatile schooling jump with ZERO moving parts.  Out came the pencil & some very rusty geometry.

A beautiful Saturday & a newly expanded stockpile of junk reclaimed lumber meant go time.  A few hours (there may have been some wandering & catching up with friends involved *ahem*), an assorted collection of leftover screws, & some precise eyeball measurements, and I’ve got “plug-n-play” eventing standards!

Possibly best safety poster.  Ever.
Your friends are already jealous of your super-fly flower box, now it’s time to blow their minds when you never have to push an angry carpenter bee out of a pin hole again (or maybe that just happens to me?).

Standard Preface from the Safety Nazi:  Dude.  Tools are awesome, but don't mess aroundWear your safety glasses, close-toed shoes, ear protection when necessary, & pay attention.  Work smarter, not harder.  You can do anything you set your mind to, but make sure you have been properly instructed, know your equipment, & always plan ahead.



Ready, Set, Go

Rule #1 of Redneck Construction (we’ll consider safety to be Rule #OptimusPrime - hey, he wears a helmet):  never be afraid to try!  No one was born with knowledge, so ask questions, google your heart out, & don’t hesitate to click my email button if you want to know more – I consider it all “paying it forward” in thanks to those who taught me.

Building Standards 16 Aug 2014 005
Let it begin...
Tools:
  • Skilsaw
  • Drill (pilot holes are especially useful in treated and/or scrap lumber, reduces cracking & other lumber fail when you drive the screws)
  • Impact Driver loaded w/ screwdriver bit (optional; you can use a screwdriver bit in your drill or a hand screwdriver)
  • Measuring Tape  
  • Pencil (or Sharpie, crayon, paint pen of your choice)
  • Wood Screws (I maintain a collection of leftovers)
Lumber:Two Frames (2) 6’ scraps (dimensions optional, but this is your base, so wide is good)
 (4) 5’ scraps (dimensions optional, mine don’t even match)
Pole Supports: As many as you like at any height you like (naturally, none of mine match here either)

Building Standards 16 Aug 2014 002
Building Standards 16 Aug 2014 003
Other Materials:  A camera so you can share your masterpiece.  A phone in case you have to dial 911 (Remember, "proactive, not reactive").  Paint/stain if you really want to go hog-wild (overachiever).

Pertinent Notes:  I wanted a 4’ standard, as I need to be able to school up to ~3’7”.  My secret ulterior motive:  this also makes the geometry EXTREMELY easy, because one vague concept I remember is the standard 3-4-5 right triangle (hello, sophomore year of high school flashback).  The frame now measures itself:  with a 4’ line from the apex down the center, it is simply two right triangles back-to-back.  Each angled side must then be 5’ and the base, 6’ (two triangles combined = 3’ X 2).

Yeah, just look at the picture up top, I’m a visual learner too, LOL!
 


Building Standards 16 Aug 2014 006 (Small)
Damn straight, it's the TFS Official Eventing Stick!
Step 1:  I like to do all my basic cuts first.  But I usually, erm, SQUIRREL!, & MAKE A KEWL THING!  Since owning a farm apparently makes you an instant hoarder, I’d been saving this sturdy little pole I’d found in the giant burn pile (included free with property purchase, LOL).  One end had splintered, but I simply cut that off, sat down with my Sharpie, & check it out:  my own handy measuring pole, labeled by USEA levels!

Building Standards 16 Aug 2014 012 (Small)
Frame layout
The Actual Step 1:  Cut the basic frame boards to length (for both standards) & lay them out.  Yes, these ARE three boards of completely different dimensions & age, heh.  My 6’ base is at the bottom of the photo & the two 5’ sides are angled around the 4’ upright.

The 4’ board is NOT included/attached to the standard, I just used it as a guide for the other three boards.  And I may or may not have gotten a little excited with the Sharpie & decided it needed to have the levels pre-marked & labeled too (hey, I might need a back-up measurer).

Building Standards 16 Aug 2014 013 (Small)
4' reference upright
Step 2:  I suck at miter-ing.  A lot.  To trim the angles you see in the standing frame, I very scientifically overlapped the boards in the final configuration, squinted one eye, & sketched the trim lines.  Then, I just nipped the corners with the skilsaw.  Close enough.

Since there will be cross-boards screwed on to the frame, you don’t need to worry if your joints are a little gappy (not the ones in  your body, I can’t help with those).  The support boards will reinforce the frame & your finished product will be very solid.  At present, there is only one screw at each joint.

Building Standards 16 Aug 2014 014
First completed frame
I also did a slight design modification.  If all your lumber matched (boring!) and you had actual miter skillz, you would fasten each side to the top surface of the base.  However, since I was working with some boards that were narrow & some that were quite old, I decided to drive the screws through the wider face of the angled boards into the thicker sides of the base.  It worked out very well & let me avoid splitting the edges of my thinner lumber.

   
Building Standards 16 Aug 2014 015 (Small)
Adding the first crosspiece
Step 3:  Do a little dance!  The hard part is done!  Now it’s time for the crosspieces, which will hold your poles/branches/panels/whatever else you can think of.

I laid out my 4’ guide upright, but I don’t have a t-square & didn’t feel like getting fussy with the level.  After laying down each cross-board, I also measured the vertical distance from the base to the top of the crosspiece on each side.  Now I could be sure that my poles would be supported at the heights I wanted & I marked the positions with my sharpie before I drilled.

Building Standards 16 Aug 2014 017
Labeled by USEA level!
Step 4:  I was getting hungry & didn’t feel like ripping new boards down with the saw at this point (project honesty).  This translated to making do with the scrap assortment I had in front of me.  I had enough to cover the essentials, though.  This finished standard has supports at 2’, 2’7” (BN), and 3’3” (T).  Of course I labeled them!!

Building Standards 16 Aug 2014 016 (Small)
One standard, AH AH AH!!
Step 5:  Repeat steps 1-4.  It goes much more quickly now that you have experience!  For now, my 2nd standard has only BN & T crosspieces, but later additions are a snap.

Step 6:  JUMP SWEET JUMPS!  Ok, I haven’t gotten this far yet, but if you do, picture submission is required!!

Building Standards 16 Aug 2014 018
All done!  Well, for today.
Future Finesse

I have a few touches left to finish (after significant snack-age).  Extras for you to consider:

  • Add a short scrap perpendicular to the end of each base if feet are needed for stability.
  • Cut the corners off crosspieces to reduce pointy edges.
  • Use molding scraps or other small wood pieces to make blocks on the end of crosspieces to prevent pole rolling.
  • Cut scoops or notches in crosspieces to hold poles like a cup.
  • Cut multiple notches in crosspieces on the inside of the triangle; you can make cavalleti, oxers & triple bars with just one pair of standards!
  • Paint it pretty, or stain to seal if you prefer the natural wood finish.
  • Drill holes in the baseboard for flowers, pinwheels, or other decoration.
  • What else can your imagination dream up??

3 comments:

  1. I love this! I've never actually bought any jump standards myself, why pay hundreds when you can build one yourself?? You're right about jump cups though, they're totally maddening (and I heard ya about poking wasps out of the holes...) I gotta admit though, I'm having trouble picturing where exactly poles go and how it stands up...need a picture update when you get the chance to put them to use!

    ReplyDelete
  2. Intriguing...how does it stand up though?

    ReplyDelete
  3. Oh, glad to hear the insects in jump holes are not just angry at me in particular!!

    Abigail and Carla, I confess that my self-assignment for last week was to rough finish them and set them up. However, my boss decided I needed to go drag myself around in cold rivers instead, the big meanie!

    I will definitely post a photo update when I get one -- in short, Carla, you have three choices to stand them up. If I was more dedicated to lumber "reclaiming" or, say, had more than $0, I would use a wider board for the base (10-12") and they would easily stand on their own.

    However, since I can claim neither of those accomplishments, I rely on clicker-trained raccoons to steady them on windy days. They do get distracted at times by my burrowing crayfish and wander off at inopportune moments, so I will go to option 3, which is simply tack on some short cross-boards on the end as feet (photo will be taken...after I have finished disciplining those naughty raccoons... ;P

    ReplyDelete